【US &Free Ship 】3Axis Nema34 Stepper Motor 1600oz.in 3.5A&Driver CNC kit

Description

Fast shipping to US!
This item will be shipped from US local warehouse by UPS. US Customers (except for Alaska, Hawaii & Puerto Rico) will receive this item fastly.
The more importance is that US customers dont need to pay Import Custom duty & fees. (Becuase it is domestic shipping)
This item includes:
3 PCS Nema 34 stepper motor with Single shaft, 1600oz.in, biloar
3
PCS
Stepper motor driver , peak 7.8A 24-80VDC
3 PCS Power supply 350W(60VDC/5.8A)
1
PCS
Breakout Board & Parallel cable ( free offering when you buy all above)
Features:
1.High torque, More smooth movement
2.High efficiency, energy-saving, low noise, low vibration, high start torque, low start current and reliable performance.
3.We offfer mach 3 software by free,if you want please download on our website.
After you payment,I will send electronic manual to your e-mail
,if you not receive,you tell me your e-mail,I
wi
ll send to you.
Detailed information :
1. Nema 34 stepper motor:
Technical Specifications
Part No.:
34HS
5435C-37B2
Frame Size:                     NEMA34
Phase:                 2 Phase
Step Angle:                    1.8 degree
Current:
3.5
A
Rated Voltage:         5.6V
Resistance:
1.6
Ohm/phase
Inductance:
22
mH/phase
Holding torque:           1
600
oz-in     (
10.5N
.m)
Detent torque:
24.5N
.cm
Rotor inertia:
3600
g
.
cm
²
Number of wire leads:   4
(
R
ed
A+
,
Green
A-
,
Yellow
B+
,
B
lue
B-
)
Weight:
5
kg
Length:
151
mm
T
he diameter for motor shaft is 14mm
2.Stepper motor driver:
Introduction:
DM860A  is a type  of two-phase hybrid stepping motor driver, The drive voltage of which is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 110mm outside diameter and less than 8.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on.
Features:
l         High performance, low price
l         Average current control, 2-phase sinusoidal output current drive
l         Supply voltage from 24VDC to 80VDC
l         Opto-isolated signal I/O
l         Overvoltage, under voltage, overcorrect, phase short circuit protection
l         14 channels subdivision and automatic idle-current reduction
l         8 channels output phase current setting
l         Offline command input terminal
l         Motor torque is related with speed, but not related with step/revolution
l         High start speed
l         High hording torque under high speed
Electrical specification:
Input voltage
24-80VDC
Input current
＜ 6A
Output current
2.8A～7.8A
Consumption
Consumption：80W；  Internal Insurance：10A
Temperature
Working Temperature -10～45℃；
Stocking temperature -40℃～70℃
Humidity
No condensation, no water droplets
gas
Prohibition of combustible gases and conductive dust
weight
500G
Pins assignments and description:
1)   Connector Pins   Configurations
Pin Function
Details
PUL +,PUL-
Pulse signal, PUL+ is the positive end of pulses  input pin
PUL- is the negative end of pulse  input pin
DIR+,DIR-
DIR signal: DIR+ is the positive end of direction input pin
DIR- is the negative end of direction input pin
ENBL+
Enable signal:  ENBL+ is the positive end of direction input pin. This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver.
ENBL-
ENBL- is the negative end of direction input pin. Usually left unconnected (enabled)
2) Pins wiring diagram:
PC’s control signals can be active in high and low electrical level. When the high electrical level is active,
all control negative signals will be connected together to GND. When low electrical level is active, all
control positive signals will be connected together to public port. Now give two examples( Open collector
&PNP),
please check them:
Fig 1. Input port circuit (Yang connection)
PC open connector output
Fig. 2 Input port circuit ( Yin connection)
PC PNP output
Note: When VCC=5V, R=0
When VCC=12V, R=1K, ＞1/8W
When VCC=24V, R=2K,＞1/8W
R must connect in the control signal part .
3.Function choice ( Using DIP pins to achieve this function)
1) Micro step resolution is set by SW 5,6,7,8 of the DIP switch as shown in the following table:
SW5
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SW6
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
SW7
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
SW8
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
PULSE/REV
400
800
1600
3200
6400
12800
25600
51200
1000
2000
5000
10000
25000
50000
2) Standstill current setting
SW4 is used for this purpose. OFF meaning that the standstill current is set to be half of the selected dynamic
current and ON meaning that standstill is set to be the same as the selected dynamic current.
3) Output current setting:
The first three bits (SW 1, 2, 3)of the DIP switch are used to set the dynamic current. Select a setting
Closest to your motor’s required current
Output current (A)
SW1
SW2
SW3
PEAK
RMS
ON
ON
ON
2.80
2.00
OFF
ON
ON
3.50
2.50
ON
OFF
ON
4.20
3.00
OFF
OFF
ON
4.90
3.50
ON
ON
OFF
5.70
4.00
OFF
ON
OFF
6.40
4.60
ON
OFF
OFF
7.00
5.00
OFF
OFF
OFF
7.80
5.60
4) Semi-flow  function:
Semi-flow function is that there is not step pulse after200 ms, the driver output current automatically
reduced to 40% of rated output current, which is used to prevent motor heat.
4. Pins of motor & power:
Motor and power pins
1
A+
Motors wiring
2
A-
3
B+
4
B-
5,6
DC+ DC-
Power supply
Power supply ：DC24-80VDC
The peak input current can not up to 6A
5. Mechanical Specification:
To have 20mm of space around ,cannot be placed next to other heating devices. What’s more, avoid dust, oil mist, corrosive gas, heavy humidity and high vibration. (Unit=mm)
6. Adjustment of troubleshooting
1) , the status on light’s indication
PWR: green, normal work light.
ALM: red, failure light, the motor with phase short-circuit, overvoltage and under-voltage protection.
2) Troubles
Alarm indicator
Reasons
Measures
LED off turn
Wrong connection for power
Check wiring of power
Low-voltages for power
Enlarge voltage of power
Motor doesn’t run, without holding torque
Wrong connection of stepper motor
Correct its wiring
RESET signal is effective when offline
Make RESET ineffective
Motor doesn’t run, but
maintains
holding torque
Without input pulse signal
Adjust PMW & signal level
Motor runs wrong direction
Wrong wires’ connection
Change connection for any of 2 wires
Wrong input direction signal
Change direction setting
Motor’s holding torque is too small
Too small relative to current setting
Correct rated current setting
Acceleration is too fast
Reduce the acceleration
Motor stalls
Rule out mechanical failure
Driver does not match with the motor
Change a suitable driver
7. Driver wiring
A complete stepper motor control system should contain stepper drives, DC power supply and controller (pulse source).
3.Power Supply
350W-60V
4. Breakout Board & 1 pc parallal cable
General in the software
P2 P3 is set to X-axis for the X-axis pulse
P4 P5 is set to Y-axis, Y axis pulse
P6 P7 is set to Z-axis Z-axis pulse
The other can be set to A B C axis
A-axis pulse P8 P9 is set as the A axis
P14 is set to B-axis B-axis pulse P1
P16 P17 is set to C-axis, C axis pulse
Can also be set to the spindle control signal \ electrical permit
Input interface for the P10 P11 P12 P13 P15
Description:
• Built in DB25 male connector.
• DB25 Output Pin:P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17.
• DB25 Input Pin: P10,P11,P12,P13,P15.
• DB25 GND Pin: P18-P25.
• Power supply: +5V DC.
• Built in C-class Optical-coupler.
• Hi
gh quality with Surface-mount Tech.
Application:
Our Stepper Motors are used on small to mid-sized CNC mills or milling machines, CNC lathes, Pick-n-place machines,Laser Engravers and Laser Cutters, Vinyl Sign Cutters, CNC Plasma Cutters, and CNC Foam Cutters. Carver machine ,Dispenser,Automazation,3D Printer,Stage lighting,instrument,laser
equipment,scanner Dispenser
,Logistics equipment,
and so on.These motors have been used in precision telescope positioning systems and robots.